Deck/Sheathing The surface, usually plywood or oriented strand board (OSB), to which roofing materials are applied.
Dormer A small structure projecting from a sloped roof, usually with a window.
Drip Edge An L-shaped strip (usually metal) installed along roof edges to allow water run off to drip clear of the deck, eaves and siding.
Eave The horizontal lower edge of a sloped roof.
Fascia A flat board, band or face located at a cornice's outer edge.
Felt/Underlayment A sheet of asphalt-saturated material (often called tar paper) used as a secondary layer of protection for the roof deck.
Fire Rating System for classifying the fire resistances of various materials. Roofing materials are rated Class A, B or C, with Class A materials having the highest resistance to fire originating outside the structure.
Flashing Pieces of metal used to prevent the seepage of water around any intersection or projection in a roof system, such as vent pipes, chimneys, valleys and joints at vertical walls.
Louvers Slatted devices installed in a gable or soffit (the underside of eaves) to ventilate the space below a roof deck and equalize air temperature and moisture.
Oriented strand board (OSB): Roof deck panels (4 by 8 feet) made of narrow bits of wood, installed lengthwise and crosswise in layers, and held together with a resin glue. OSB often is used as a substitute for plywood sheets.
Penetration Vents, pipes, stacks, chimneys-anything that penetrates a roof deck.
Rafters The supporting framing to which a roof deck is attached.
Rake The inclined edge of a roof over a wall.
Ridge The top edge of two intersecting sloping roof surfaces.
Sheathing The boards or sheet materials that are fastened to rafters to cover a house or building.
Slope Measured by rise in inches for each 12 inches of horizontal run: A roof with a 4-in-12 slope rises 4 inches for every foot of horizontal distance.
Square The common measurement for roof area. One square is 100 square feet (10 by 10 feet).
Truss Engineered components that supplement rafters in many newer homes and buildings. Trusses are designed for specific applications and cannot be cut or altered.
Valley The angle formed at the intersection of two sloping roof surfaces.
Vapour Retarder A material designed to restrict the passage of water vapor through a roof system or wall.
From the National Roofing Contractors Association
One of the most critical factors in roof system durability is proper ventilation. Without it, heat and moisture build up in an attic area and combine to cause rafters and sheathing to rot, shingles to buckle, and insulation to lose its effectiveness. Therefore, it is important never to block off sources of roof ventilation, such as louvers, ridge vents or soffit vents, even in winter. Proper attic ventilation will help prevent structural damage caused by moisture, increase roofing material life, reduce energy consumption and enhance the comfort level of the rooms below the attic. In addition to the free flow of air, insulation plays a key role in proper attic
ventilation. An ideal attic has:
The requirements for proper attic ventilation may vary greatly, depending on the part of the country in which a home or building is located, as well as the structure's conditions, such as exposure to the sun, shade and atmospheric humidity. Nevertheless, the general ventilation formula is based on the length and width of the attic. It is recommended that a minimum of 1 square foot of free vent area for each 150 square feet of attic floor—with vents placed proportionately at the eaves (e.g., soffits) and at or near the ridge.
There are a number of things to consider when selecting a new roof system. Of course, cost and durability head the list, but aesthetics and architectural style are important, too. The right roof system for your home or building is one that balances these five considerations. The following roofing products commonly are used for steep-slope structures.
Asphalt shingles possess an overwhelming share of the U.S. steep-slope roofing market and can be reinforced with organic or fiberglass materials. Although asphalt shingles reinforced with organic felts have been around much longer, fiberglass-reinforced products now dominate the market.
Wood shingles and shakes are made from cedar, redwood, southern pine and other woods; their natural look is popular in California, the Northwest and parts of the Midwest. Wood shingles are machinesawn;shakes are handmade and rougher looking. A point to consider: Some local building codes limit the use of wood shingles and shakes because of concerns about fire resistance.
Slate is quarried in the United States in Vermont, New York, Pennsylvania and Virginia. It is available in different colors and grades, depending on its origin. Considered virtually indestructible, it is, however, more expensive than other roofing materials. In addition, its application requires special skill and experience. Many old homes, especially in the Northeast, still are protected by this long-lasting roofing material.
Metal, primarily thought of as a low-slope roofing material, has been found to be a roofing alternative for home and building owners with steep-slope roofs. There are two types of metal roofing products: panels and shingles. Numerous metal panel shapes and configurations exist. Metal shingles typically are intended to simulate traditional roof coverings, such as wood shakes, shingles and tile. Apart from metal roofing's longevity, metal shingles are relatively lightweight, have a greater resistance to adverse weather and can be aesthetically pleasing.
Synthetic (Resin) roofing products simulate various traditional roof coverings, such as slate and wood shingles and shakes.
A roof system's performance is affected by numerous factors. Knowing about the following will help you make informed roof system buying decisions:
All steep-slope roof systems (i.e., roofs with slopes of 25 percent or more) have five basic components:
Roof Covering: shingles, tile, slate or metal and underlayment that protect the sheathing from weather.
shingles, tile, slate or metal and underlayment that protect the sheathing from weather.
The following information has been provided in party by the National Roofing Contractors Association (NRCA) as part of their ongoing effort to educate home and building owners about roofing and roofing contractors.
A new roof system is a big investment, and you should get a quality roof system at a fair price from a professional roofing contractor. Hopefully, this information will make you a more knowledgeable consumer and, when the time comes, a smart roof system buyer.